Technical Features
| Controller Features: |
|
| Double standard |
EGSM900 / GSM1800Hz |
| EDGE (EGPRS) |
Multi-slot class 2 |
| GPRS |
Multi-slot class 6 |
| CSD |
up to 14,4 kbps |
| Integrated TCP/IP stack |
|
| Data transmission methods: |
GPRS, EDGE, SMS |
| Recommended Storage Temperature: |
-40°.. + 85°C |
| Recommended Operational Temperature: |
-20°.. + 55°C |
| GPS receiver features |
|
| Number of Channels |
20 "All-in-View" |
| Exactness: Speed determination |
0,1 m/sec., 95% |
| Time determination deviation |
1 microsecond, synchronizing with atomic clock of GPS satellites |
| Position determination time |
0,1sec. |
| Hot start |
1 sec. on average |
| Cold start |
42 sec. on average |
| Operational Temperature: |
-40°.. + 85°C |
| Exactness: Determination of |
1,4 m |
Operational Conditions
Table 1 Absolute maximum ratings
| Parameter |
Value |
| Supply voltage |
9.6..16.0 V (Voltage must never drop below the minimum value) |
| DC input voltage (any signal pin) |
-0.5 .. 5.5 V |
| Operating temperature range |
-35 .. +55 °C |
| Storage temperature range |
-40 .. +85 °C |
| Extreme relative humidity range limit |
5 .. 95% |
Table 2 Recommended operating conditions
| Parameter |
Value |
Note |
| Supply Voltage (VBB) |
12.0 V |
Voltage must never drop below the mini-mum value (see Table1) |
| Logic voltage (IO voltage) |
1.8 .. 5.0 V |
|
| DC output source or sink current (any I/O pin, user adjustable) |
0 .. 5V |
Upper limit depend¬ing on I/O voltage |
| Operating temperature range |
- 20 .. +55 °C |
|
| Relative humidity range |
20 .. 75% |
non-condensing |
System requirements PC
Operational Systems: MS Windows 98 SE, MS Windows NT 4.0, MS Windows XP
| |
Minimum requirements |
Recommended requirements |
| Processor |
Celeron 1 GHz |
Celeron 2 GHz |
| RAM memory space |
256Mb |
512Mb |
| Video memory |
32Mb |
64Mb |
| Free Hard disk space |
4 GB |
4 GB |
Additional sensors installation
- If necessary you can connect to the device additional sensors (such as temperature sensor, different volume sensors, weighing cell, unauthorized access sensors, external devices connection, including PC, pocket PC and others) by means of Slot 3.
- To connect peak sensors and buttons use "Out 1-4" for digital sensors "TX and RX". Please apply to our Help-desk for additional information.
- Attention! Do not connect sensors directly to the device but use interface circuit!
Installation (Hard) Device has 3 slots:
Slot 1 - Consists of two contacts (1,2):
- 1 - Power supply contact +12 V (on the matching bar RED cable).
- 2 - Ground (on the matching bar BLACK cable).
Slot 2 - GPS antenna connection.
| |
COLOUR |
FUNCTION |
PIN |
 |
Black |
GND |
1 |
| Red |
VCC |
2 |
| - |
NC |
2 |
| White |
RX |
3 |
| Green |
TX |
4 |
| - |
NC |
5 |
Slot 3 - Consists of ten contacts (3-12)
- 3 - Ground.
- 4 - Out 1.
- 5 - GPS Data (TTL level).
- 6 - Led + (for light diode connection).
- 7 - Led - (for light diode connection).
- 8 - GPIO 2.
- 9 - GPIO 3.
- 10 - GPIO 4.
- 11 - ТХ (TTL level).
- 12 - RX (TTL level).
To run the device connect GPS antenna (for correct operation of antenna, it is recom¬mended to place antenna in a way it is not covered by metal) and Slot 1 connected to the steady power supply 12V (operating voltage 9-16V). By switching on the light-indi¬cator GPS antenna will inform you about system start, and flashing signal of light-indi¬cator determines that data is liquid, it is transferred, and in case of GSM network failing, it is accumulated by the device.
